1. Set accessibility names for the buttons for applying a macro to the project or files. Note that although these names are not read by NVDA 2018.2, they will be read by NVDA 2018.3
2. Remove access keys from wxStaticText controls, as they do not work on this type of control.
This fix addresses the remaining issue, issue 4, that the selection was often cleared when Play-at-Speed stopped.
The problem was that Scrubbing 'Set Selection to here' code was not being disabled by the Play-at-Speed state.
LUFS are defined as the power of the signal, not as the root mean square.
Accidential use of the RMS caused incorrect normalization to only half
of the LUFS value.
Please note that normalizing to large LUFS values may introduce clipping
of large peaks. However, the recommended target value in EBU R128 of
-23 LUFS should be totally safe but only uses a small amount of the
possible quantization range. For tracks with normal dynamic range,
normalizing to about -10 LUFS should be possible without clipping.
... Replace some enum constants with the equivalent values from the more
special-purpose enums, as the wx header files recommend, so overloading
selects the ctors with non-int arguments.
In a full rebuild of the debug project on Mac, this reduces the count of
warnings from 264 to 274.
This possible fix is based on the idea that YieldFor is flaky, and is holding up events that we SHOULD process.
Therefore we process ALL events, not just some, and we do two yields, in case we are getting behind on the queue.
Now cut-preview and looped play revert to using the old fixed speed play-at-speed.
Unfortunately Scrubbing does not (yet) support looped play or cut-preview.
In particular, device toolbar previously could be made ridiculously small.
Also in the default configuration it takes a whole line, so we now use that space in its initial size.
Mixer Toolbar initial size was a little small. Now it matches the Transport Toolbar width.
Meter Toolbar initial size was too small.
Transcription Toolbar was a little too small. Better to start out slightly wider than previously.
Fixed issue 2, i.e. the scrub indicator no longer appears during Play at Speed, and the status bar now says 'Playing at Speed' rather than 'Scrubbing'.
Worth doing for users with wide screens, who want to use the toolbar at full screen width.
Both toolbars can now expand to a little over 2000 pixels width.
Note that the max sizes affect what is drawn. You can make the toolbars wider still, but the sliders inside them won't continue to lengthen.
I moved 'Fit()' from ToolBars into MeterToolBar, because it is a workaround for an incorrect size calculation by MeterToolBar. MeterToolBar is sized as if there is no resizer, so when there is one, the toolbar needs to be expanded (using Fit) to accommodate the resizer.
I also set the min size of MeterToolBar to 150, so that some meter will appear, even if Toolbar shrunk to the minimum.
This adds a new preference to Playback prefs, VariSpeedPlay, on by default, which makes it possible to vary the playback speed slider whilst audio is playing using play at speed. The code uses the Scrubbing playback engine.
This code is not final, but is already useful. Known issues:
1- Playback does not stop and pop-up the Play at Speed button at the end of playing the selection.
2- The scrub widget shows uselessly on the scrub ruler when in Play at Speed mode and the status bar proclaims 'Scrubbing'.
3- At low speeds the playback is clicky, with VariSpeedPlay, even if no changes to speed are being made.
If we can't fix both 1 and 2 by 2.3.0 release time, VariSpeedPlay will be made false by default.
Now shown as "Nyquist Effects Prompt" (in Effects menu) and "Nyquist Tools Prompt" (in Tools Menu).
These prompts will have slightly different behaviour, e.g. only tools allow aud-do.
Changes to the state of the track which are appended to the track name, as suggested by Robert.
Mute On becomes Muted.
Solo On becomes Soloed.
Select On becomes Selected
Sync Lock Selected becomes Sync Locked.
